MTS-SAS Series - 1 to 15 SAS/SATA HDD/SSD Duplicator and Sanitizer(MTS1600SAS)
U-Reach MTS-SAS series is a professional SATA/SAS HDD duplicator, specially designed for high volume duplication. Equipped with U-Reach ‘s unique multitasking technology. The MTS-SAS series Hard Drive duplicator can simultaneously copy all targets and with a high transfer speed up to 18GB per minute. We guarantee highest productivity without speed degradation, even when the number of targets increase.
The MTS-SAS series SAS/SATA Hard Drive duplicator provides four copy modes: quick copy, all partitions copy, percentage copy and whole HDD copy that all meet different duplication task requirements. NTFS, Linux (Ext2/Ext3/Ext4), FAT/FAT32 and Mac (HFS, HFSX, HFS+) are supported formats with quick copy. Quick copy mode copies data and skips blank area; this mode enhances copy speed.
In addition, the MTS-SAS series SAS/SATA HDD duplicator is equipped with different levels of secure erase functions, Quick Erase, Full Erase, DoD 5220 Erase government standards and Secure Erase, which can fulfill different levels of HDD wiping security.
|Speed||18GB/min. (300MB/sec.) *Actual performance is dependent on HDD transfer rates.|
Copy Modes: All Partitions/Whole HDD/Percentage copies all types of formats, both known, and unknown.
Quick Copy: FAT16/32/64, Windows (NTFS), Mac (HFS/HFS+/HFSX), and Linux (Ext2/3/4).
Stand-alone, non PC-based operation
Backlit Monochrome LCD Display
3 LED Indicators per Port:
Yellow (Power), Green (Pass), Red (Fail)
4 Push Buttons (▲, ▼, OK, ESC)
Quick Copy, All Partitions Copy, Whole HDD Copy, and Percentage Copy
Manually set (Bad sector) threshold range to skip during copy process
Bit-by-bit hardware-accelerated data comparison
Quick Erase, Full Erase, DoD Erase, 7 write erase, Secure Erase,
Enhance Secure Erase, and NSA Erase
Real-time status monitoring through PC
Monitor real-time recordings and Log Reports via PC-Link
Event log reports are generated through the USB port and saved to USB devices
All (Windows, Linux, and other stand-alone systems)
1.8"/2.5"/3.5” SATA/SAS HDDs and SSDs
IDE, microSATA, mSATA and M.2
Supports MBR, GPT, and Advanced formats.
Embedded controller is designed to support capacities over 18TB+.
Constant improvement supports latest market-available devices.
Selectable Voltage 115V or 230V, 50/60Hz
Operating Temperatures: 5°C ~ 45°C (41°F ~ 113°F)
Storage Temperatures: -20°C ~ 85°C (-4°F ~ 185°F)
Working Humidity: 20% ~ 80%; Storage Humidity: 5% ~ 95%
FCC, CE, RoHS
Impeccable High Speed
U-Reach MTS-SAS Series SATA/SAS HDD/SSD duplicator is capable of copying at 18GB/min. on all targets simultaneously, without any speed degradation as number of targets increase. This duplicator is great for manufacturers.
Intelligent Duplication Modes
U-Reach MTS-SAS SAS HDD duplicator offers a diverse of duplication modes. The user may select the appropriate mode based on application demand.
Illustration of Copy Modes
The areas containing data are marked in blue. The areas being copied are marked in red. Duplication time depends on the speed supported by the hard drive's controller chip.
Erase HDD index table, and only takes A FEW SECONDS to complete.
Erases the entire HDD.
Complies with U.S. Department of Defense erasure standards.
A National Institute of Standards and Technology 800-88 accepted
technique for properly purging hard drives. This method is supported by almost all modern SATA/SAS HDD.
Fast Erase Key
Fast Erase Key enables the end-user to perform erase functions asynchronously.
Auto Rejection of Slow Devices
MTS-SAS Series HDD/SSD duplicator enable end-users to set the minimum writing speed threshold. This feature was developed to prevent and to eliminate problematic devices that halts the duplication and sanitizing process.
Double Data Verification: Compare + CRC Checksum
U-Reach duplicators makes straightforward copies, but it is imperative that the copied data are verified through a bit-by-bit process, this will ensure successful copied and reduce customer recalls.
Skipping Bad Sectors
End-users are given options to skip bad sectors from the source device. Access the function to select the numbers of bad sectors to skip, from 0 through unlimited.
Optional Adapters Supported
Event Log Report
USB Drive Duplicator
SD/microSD Card Duplicator
CF/CFast Card Duplicator
SATA DOM/eMMC DuplicatorHDD/SSD Duplicator
SATA/SSD HDD Duplicator
SAS HDD Duplicator
CRU HDD Duplicator
M.2 NVMe PCIe SSD DuplicatorDisc DuplicatorAccessoriesSupport
Write Protect Solution Flash Duplicator
Flash Card Mass Duplicaton
Flash Quality Checking Tools
HDD Data Secure Sanitizer
iSecuLog Tamper-free Log Report
Various Interface HDD DuplicatorNewsAbout U-Reach
ISO CertificationContact U-Reach
Copyright © 2021 U-Reach Inc. All rights reserved